For people who are suspecting there might be molds growing in the house, whether it is on walls or in rooms, it will need to be eradicated. The molds might be found in closets also and it is essential to know what type of mold you are dealing with before starting to clean up. There are types which are harmless and which cause allergies such as itching or irritation. When considering mold testing Illinois residents need to be versed with what it involves.
There are many different types of kits available and they have varying modes of operation. One of them is the lift tape kit which is ideal in cases where you are certain molds are present but want to determine the strain. It is effective when testing surfaces of furniture, walls and floors. You need to peel back the tape from the tacky surface. You then press the sticky side in a gentle way on the surface with molds. When that is done, the cover is replaced over the sticky surface and the samples taken for tests.
The instant kit does the confirmation in about 10 minutes. It however only confirms that what you have is mold and not the specific type. You will still need lab analysis for determination of whether it is toxic or not. It is used by removing the swab from the tube before swabbing the suspect area. The swab is then taken back into the tube and left for some 10 minutes after shaking in the test tube. The color is checked against a chart to determine final result.
There is the viable kit which has most uses. This test does not need lab tests. It is useful for establishment of whether molds are present plus the strain. Air quality can also be tested.
The kit comes with a petri dish with gel and a swab. To carry out the test, the suspect areas are swabbed before having it rubbed over that gel. The lid will be replaced to enable the sample to germinate for a number of days. It usually takes 3 to 7 days. If you look to test quality of air in a room, two kits are needed. After lids are removed from them, you place one in a room and another close to the same room.
The kits are left in place for an hour so before the lids are replaced. After 7 days, there should have been growth of molds. You then compare both results. If they both produce same strains, then the molds are merely representing what is in the general environment. If there are differences, you will need to take samples for lab testing.
There are situations in which the tests might yield inconsistent results. Determination of toxicity might be a challenge. Testing for molds and testing for their toxicity are two different things, which makes it difficult to get conclusive results.
The decision on the way to eradicate the molds is a challenge as well. This is because most eradication is done in the same manner. This means knowing molds that are present does not change mode of removal.
There are many different types of kits available and they have varying modes of operation. One of them is the lift tape kit which is ideal in cases where you are certain molds are present but want to determine the strain. It is effective when testing surfaces of furniture, walls and floors. You need to peel back the tape from the tacky surface. You then press the sticky side in a gentle way on the surface with molds. When that is done, the cover is replaced over the sticky surface and the samples taken for tests.
The instant kit does the confirmation in about 10 minutes. It however only confirms that what you have is mold and not the specific type. You will still need lab analysis for determination of whether it is toxic or not. It is used by removing the swab from the tube before swabbing the suspect area. The swab is then taken back into the tube and left for some 10 minutes after shaking in the test tube. The color is checked against a chart to determine final result.
There is the viable kit which has most uses. This test does not need lab tests. It is useful for establishment of whether molds are present plus the strain. Air quality can also be tested.
The kit comes with a petri dish with gel and a swab. To carry out the test, the suspect areas are swabbed before having it rubbed over that gel. The lid will be replaced to enable the sample to germinate for a number of days. It usually takes 3 to 7 days. If you look to test quality of air in a room, two kits are needed. After lids are removed from them, you place one in a room and another close to the same room.
The kits are left in place for an hour so before the lids are replaced. After 7 days, there should have been growth of molds. You then compare both results. If they both produce same strains, then the molds are merely representing what is in the general environment. If there are differences, you will need to take samples for lab testing.
There are situations in which the tests might yield inconsistent results. Determination of toxicity might be a challenge. Testing for molds and testing for their toxicity are two different things, which makes it difficult to get conclusive results.
The decision on the way to eradicate the molds is a challenge as well. This is because most eradication is done in the same manner. This means knowing molds that are present does not change mode of removal.
About the Author:
If you are searching for information about mold testing Illinois residents can come to our web pages today. More details are available at http://www.moldprochicago.com/moldprochicago.com/mold-services now.
