If you want to varnish your floor, there are companies that have come up with guidelines so that you can have a better understanding of the process of varnishing the floors. The steps may differ from company to company, but the overall procedure is the same. Floors that have not been burnished will have a coating or adhesives that will have to be removed by the use of machines. Below are the guidelines on Florida Commercial Polished Concrete
The machine uses rough diamonds that are made of metal. If the aggregate present in the floor has been exposed, the burnish from the first pour has to be removed too. This process is a bit complex than many people think thus it requires technicians that are both qualified and experienced.
Surface grinding is usually the initial step. Before that, there is a test that has to be done to check how hard the surface is. This test is important because it helps the technicians to select the right tools that will be suitable for that particular floor. After the test, the grinding is then done using diamond tooling that is appropriate for that type of floor.
After the grinding is completed, stains and densifier are applied on floors. The removal of the top thin layer makes these floors to be soft and weak; the densifier will help in hardening the surface once more. The stain is applied first, and when it dries, the densifier is applied, and the slab is kept wet for almost 30 minutes. A second coat of the densifier is applied if the first coat is not enough.
After a few minutes, honing is done on floors after making sure that the densifier has dried. Diamond pads that have grit close to 500 are used for this process. After some minutes, one can observe a glossy mirror-like look on the surface. However, it can take longer before the glossiness starts to appear hence making the technicians work for longer hours than usual.
The next procedure is to polish the floor. The remaining diamond pads that have grits ranging from 1500-3000 are used in this step. The floor is then varnished according to the demands of the clients. Some clients like mirror-like surfaces smooth, thus a lot has to be done. Other clients prefer somewhat dull appearances thus it is important to know what the customer wants.
Polishing pads are used to finish the varnishing process giving the slab the required degree of smoothness. This step requires one to be patient so that they can achieve the desired results. Also, the technicians that you hire should have certification to show that they are qualified so that they do not perform sub-standard work on your floor thus one has to ensure a lot of care when hiring them.
If the steps are followed to the latter, you will end up with a perfectly varnished floor. However, as stated earlier, the steps may vary from company to company thus it is important that you follow the guidelines provided by the company that you have selected to do the job but the end products are usually the same.
The machine uses rough diamonds that are made of metal. If the aggregate present in the floor has been exposed, the burnish from the first pour has to be removed too. This process is a bit complex than many people think thus it requires technicians that are both qualified and experienced.
Surface grinding is usually the initial step. Before that, there is a test that has to be done to check how hard the surface is. This test is important because it helps the technicians to select the right tools that will be suitable for that particular floor. After the test, the grinding is then done using diamond tooling that is appropriate for that type of floor.
After the grinding is completed, stains and densifier are applied on floors. The removal of the top thin layer makes these floors to be soft and weak; the densifier will help in hardening the surface once more. The stain is applied first, and when it dries, the densifier is applied, and the slab is kept wet for almost 30 minutes. A second coat of the densifier is applied if the first coat is not enough.
After a few minutes, honing is done on floors after making sure that the densifier has dried. Diamond pads that have grit close to 500 are used for this process. After some minutes, one can observe a glossy mirror-like look on the surface. However, it can take longer before the glossiness starts to appear hence making the technicians work for longer hours than usual.
The next procedure is to polish the floor. The remaining diamond pads that have grits ranging from 1500-3000 are used in this step. The floor is then varnished according to the demands of the clients. Some clients like mirror-like surfaces smooth, thus a lot has to be done. Other clients prefer somewhat dull appearances thus it is important to know what the customer wants.
Polishing pads are used to finish the varnishing process giving the slab the required degree of smoothness. This step requires one to be patient so that they can achieve the desired results. Also, the technicians that you hire should have certification to show that they are qualified so that they do not perform sub-standard work on your floor thus one has to ensure a lot of care when hiring them.
If the steps are followed to the latter, you will end up with a perfectly varnished floor. However, as stated earlier, the steps may vary from company to company thus it is important that you follow the guidelines provided by the company that you have selected to do the job but the end products are usually the same.
About the Author:
You can find details about the benefits you get when you install Florida commercial polished concrete floors at http://www.concretereflections.com right now.
